Stufin
Home Quick Cart Profile

Turbidity Sensor

Turbidity Sensor Turbidity Sensor
Buy Now

Temperature range

0C to 50C (32F to 122F)

Pressure range

Up to 10 bar (145 psi)

pH range

2 to 12

  • Housing and Materials: The sensor is typically housed in a rugged, waterproof enclosure made of materials such as stainless steel, polycarbonate, or PVC.
  • Power Supply: The sensor can operate on a variety of power supplies, including DC voltage (e.g., 12V, 24V) or battery-powered options.
  • Output: The sensor can provide either analog output (e.g., 0-10V, 4-20mA) or digital output (e.g., RS-485, Modbus, I2C).
  • Certifications: Turbidity sensors often carry certifications such as IP67, IP68, or ISO 7027, ensuring compliance with industry standards.

Applications

  • Water quality monitoring in drinking water treatment plants, wastewater treatment plants, and environmental monitoring stations.
  • Industrial process control in chemical, pharmaceutical, and food processing industries.
  • Aquaculture and aquarium management.
  • Swimming pool and spa monitoring.
  • Oil and gas exploration and production.
Turbidity sensors are used in a wide range of applications, including

Technical Specifications

Please refer to the specific datasheet or product documentation for detailed technical specifications, as they may vary depending on the manufacturer and model of the turbidity sensor.

Pin Configuration

  • Turbidity Sensor Documentation
  • Overview
  • The Turbidity Sensor is a device used to measure the cloudiness or haziness of a fluid, typically water or air, by detecting the amount of light scattered by suspended particles. The sensor provides a digital output signal that is proportional to the turbidity level.
  • Pin Description
  • The Turbidity Sensor has a total of 5 pins, labeled as follows:
  • 1. VCC (Power Supply)
  • Pin description: Positive power supply pin
  • Function: Provides power to the sensor
  • Voltage range: 3.3V to 5V
  • Connection: Connect to a power source (e.g., Arduino board, breadboard, or direct to a battery)
  • 2. GND (Ground)
  • Pin description: Negative power supply pin (ground)
  • Function: Provides ground reference for the sensor
  • Connection: Connect to a common ground point (e.g., Arduino board, breadboard, or direct to a battery)
  • 3. SCL (Clock)
  • Pin description: I2C clock pin
  • Function: Used for I2C communication protocol
  • Connection: Connect to the SCL pin of the microcontroller (e.g., Arduino board) or other I2C devices
  • 4. SDA (Data)
  • Pin description: I2C data pin
  • Function: Used for I2C communication protocol
  • Connection: Connect to the SDA pin of the microcontroller (e.g., Arduino board) or other I2C devices
  • 5. INT (Interrupt)
  • Pin description: Interrupt pin
  • Function: Outputs an interrupt signal when the turbidity level exceeds a certain threshold (configurable)
  • Connection: Connect to an interrupt pin on the microcontroller (e.g., Arduino board) or use an external interrupt handler
  • Connection Structure
  • To connect the Turbidity Sensor to a microcontroller (e.g., Arduino board), follow this structure:
  • 1. VCC_pin -> 3.3V or 5V power supply
  • 2. GND_pin -> Ground
  • 3. SCL_pin -> SCL_pin of the microcontroller
  • 4. SDA_pin -> SDA_pin of the microcontroller
  • 5. INT_pin -> Interrupt pin of the microcontroller (or external interrupt handler)
  • Additional Notes
  • Make sure to use a suitable power supply and voltage regulator to power the sensor.
  • Use a 10k pull-up resistor on the SDA line to ensure reliable I2C communication.
  • Configure the interrupt pin and threshold value according to your specific application requirements.
  • By following this documentation, you should be able to successfully connect and integrate the Turbidity Sensor into your IoT project.

Code Examples

Turbidity Sensor Documentation
The Turbidity Sensor is a device used to measure the cloudiness or haziness of a fluid, typically water or air. It is an essential component in various IoT applications, such as water quality monitoring, industrial process control, and environmental monitoring.
Technical Specifications:
Measurement Range: 0-1000 NTU (Nephelometric Turbidity Units)
 Accuracy: 5% of full scale
 Resolution: 0.1 NTU
 Power Supply: 5V DC
 Communication Interface: Analog output (0-5V) or digital output (I2C or UART)
 Operating Temperature: 0C to 50C
Code Examples:
### Example 1: Arduino-based Turbidity Measurement
This example demonstrates how to use the Turbidity Sensor with an Arduino board to measure the turbidity of a water sample.
Hardware Requirements:
Turbidity Sensor
 Arduino Board (e.g., Arduino Uno)
 Breadboard and jumper wires
 Power supply (5V DC)
Software Requirements:
Arduino IDE
Code:
```c
const int turbidityPin = A0;  // Analog input pin for turbidity sensor
void setup() {
  Serial.begin(9600);
}
void loop() {
  int sensorValue = analogRead(turbidityPin);
  float voltage = sensorValue  (5.0 / 1023.0);
  float turbidity = map(voltage, 0, 5, 0, 1000);
  Serial.print("Turbidity: ");
  Serial.print(turbidity);
  Serial.println(" NTU");
  delay(1000);
}
```
In this example, the Turbidity Sensor is connected to the analog input pin A0 of the Arduino board. The `analogRead()` function reads the analog voltage output from the sensor and converts it to a digital value. The `map()` function is used to scale the voltage value to a turbidity value in NTU. The resulting turbidity value is printed to the serial console.
### Example 2: Raspberry Pi-based Turbidity Monitoring with I2C Interface
This example demonstrates how to use the Turbidity Sensor with a Raspberry Pi board to measure and display the turbidity of a water sample using the I2C interface.
Hardware Requirements:
Turbidity Sensor with I2C interface
 Raspberry Pi board
 Breadboard and jumper wires
 Power supply (5V DC)
Software Requirements:
Raspbian OS
 Python 3.x
Code:
```python
import smbus
import time
# I2C bus and address
bus = smbus.SMBus(1)
address = 0x1A
while True:
    # Read turbidity value from sensor
    data = bus.read_word_data(address, 0x00)
    turbidity = data  (1000.0 / 65535.0)
    
    # Print turbidity value
    print("Turbidity: {:.2f} NTU".format(turbidity))
    
    # Wait 1 second before taking the next reading
    time.sleep(1)
```
In this example, the Turbidity Sensor is connected to the Raspberry Pi's I2C bus. The `smbus` library is used to read the turbidity value from the sensor using the `read_word_data()` function. The turbidity value is then printed to the console using Python's `print()` function.
These examples demonstrate how to use the Turbidity Sensor in different contexts, including Arduino-based projects and Raspberry Pi-based IoT applications.